Longshine LCS-US204 User Manual Page 1

1 LCS-US204 USB 2.0 Hi-Speed-Port Device Server User’s Manual Version 1.0

10 9. If the wireless network is secured by WPA-PSK or WPA2-PSK, the key formats, shared key and encryption must be set correctly.

11 10. Click Submit to save your settings. And the server will reboot. 11. You have now finished the procedure of setting the wireless parameter

12 3.3.2 IP Address Unless you are assigning an IP address using DHCP, you must obtain an unused IP address from your network administrator.

13 4. Double click the highlighted server (or click the “Configure Server” button) to get the server’s web pages. Click CONFIG icon. 5. Log

14 6. Click the button corresponding to your choice of IP setting methods (static or dynamic using DHCP). When assigning a static IP ad

15 Chapter4 Using the USB Device Server 4.1 Introduction The goal of this produce is to provide the USB device server in a single product.

16 4.4 Installation of USB Device Driver Some USB devices, like printers or MFPs (multifunction printers), require to install vendor-supplied

17 F. Click the “Connect” button. Then the message “Manually Connect by your_computer_name” will be shown, as the following figure.

18 then click the “Disconnect” button to disconnect the USB device. Now the driver of your USB device is installed. 4.5 Using the USB Device Se

19 D. Now, PC will detect the plug-in of the USB device. The “connect” operation is a software operation that simulates an actual USB device pl

2 Table of Contents CHAPTER1 INTRODUCTION ...

20 4.6 Auto-Connect Printer The method described in section 4.5 is so-called manual-connect, which means users must manually connect the USB d

21 The following figure will appear. D. Choose the desired printer. The desired printer must be the Windows printer (this is a logical print

22 physical printer on the server. F. Then try to issue a print job to the desired printer. You will see the Control Center will automatical

23 If you would like to break the association between the Windows printer and the physical printer, just click on the associa

24 C. Click the “Network Scanner” button. Then you can see that the Control Center will automatically do a “connect” operation. The following w

25 E. Follow the usual steps to do scanning. F. After the scanning, close the “Auto-Connect Scanner” window. At this moment, Control Center wi

26 You can see the storage icon in the system tray. Then just use the new disk as a general disk. After you finish the disk operations, click

27 At this moment, the user on the TEST computer will see the following window, indicating that another computer – TESTES is reques

28 Chapter5 File Server This chapter describes the file server function of the Server which allows USB storage devices to be shared across a n

29 - When do you need to configure codepage? The Server supports Windows codepages. If users want to communicate files using FTP client tool or S

3 CHAPTER7 TROUBLESHOOTING...38 7.1 LED Indicators

30 5.4 Using Shared Storages by SMB/CIFS Method for Windows 1. Connect a USB storage device to this product. 2. Select My Network Places. 3.

31 to the Server. You can add user name and password in User Account box by the Control Center or the Server’s Web page.  Note: If you use SMB on

32 4. Perform FTP commands to use this FTP server.

33 Chapter6 The Server’s Web Pages 6.1 Introduction The Server runs the http server, httpd on TCP port: 80. Users may use the web pages to

34 6.2.2 Setting up Server Configuration To set up the Server configuration, click on the “CONFIG” icon ad then the system will request user to

35  TCP/IP: You have to set the Server’s TCP/IP configuration to connect TCP/IP network. Please see Chapter 3 Basic Installation for

36  Administrator: enter your desired administrator name.  New Password: enter your desired password.  Re-type Password: re-confirm the pass

37

38 Chapter7 Troubleshooting This chapter provides useful information to help you resolve difficulties that you may experience with your Server

39 Chapter8 Restore Factory Defaults You may restore the Server’s default parameters by one of the following methods. 8.1 Using the Server’s

4 Chapter1 Introduction Thank you for purchasing LCS-US204 USB Device Server (in the following referred to as “Server”). This Server is design

40  Static IP: Disabled - IP Address: 192.168.1.100 - Subnet Mask: 255.255.255.0 User Accounts  Administrator: admin  Password: admin

41 Chapter9 Upgrade Firmware This chapter describes how to upgrade firmware. Please follow one of the following Procedures: Procedure A:

42 Chapter10 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the pow

43 Chapter11 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the l

5 Chapter2 Product Overview 2.1 Package Contents Verify that nothing is missing from the package by using the checking list bel

6  USB scanner  USB storage (like USB external HD, flash disk, and digital camera)  USB speaker  USB camera  USB digital TV tuner  USB

7 Chapter3 Basic Installation 3.1 Connecting the Hardware 1. Make sure that your USB devices are switched off and that the Server’s Power

8 USB Device Server Control Center. 3. If the tool finds USB device servers in your local area network, then you have to select a server from the

9 6. Click Wireless icon. 7. In order to join an existing wireless network, you have to set the correct SSID, and the correct security m